Three Things to Improve High-Speed PCB Signoff, Part 2
September 27, 2023 | Brad Griffin, Cadence Design SystemsEstimated reading time: 1 minute
Another challenge for SerDes is losses within the channel design. At high speeds, dielectric material can be very lossy, making the appropriate selection of the right material, length, etc., critical for the channel. Many questions about stackup, trace widths, and height from the ground plane need to be defined up front. Simulating a signal with a topology explorer tool extracted from the design can be used to set up and run sweep parameters and push min/max length/spacing values into the Allegro schematic constraint manager (system capture). The preliminary constraints and schematics flow is illustrated in Figure 1. As the design progresses with final decisions on stackup and material selections, these constraints can be adjusted.
With the schematics phase finished and the layout phase in progress, the next challenge is compliance with specifications. Specs are dependent on the technology—PCI Express (PCIe), USB, etc.—and, because each one has its own requirements, this can be a complicated process. During this analysis, it is important to make sure the correct transmitter and receiver IBIS-AMI models are being used.
For the channel, Cadence tools can be used to accurately model the channels and address specifications. This is done by using the board file created by the layout designer, selecting several or all the lanes (depending on how much time is available), and running either a 2.5D or full 3D analysis on the entire channel.
Using the results of the channel extraction, a compliance analysis can be run based on the desired protocol. Most likely this will not be a one-time event, as often some obscure requirement not identified in the preliminary phase will surface, requiring additional iterations.
To read the rest of this article, which appeared in the September 2023 issue of Design007 Magazine, click here.
Suggested Items
Connect the Dots: Designing for Reality—The Pre-Manufacturing Process
05/08/2024 | Matt Stevenson -- Column: Connect the DotsI have been working with Nolan Johnson on a podcast series about designing PCBs for the reality of manufacturing. By sharing lessons learned over a long career in the PCB industry, we hope to shorten learning curves and help designers produce better boards with less hassle and rework. Episode 2 deals with the electronic pre-manufacturing process. Moving from CAD (computer-aided design) to CAM (computer-aided manufacturing) is a key step in PCB manufacturing. CAM turns digital designs into instructions that machines can use to actually build the PCB.
Real Time with… IPC APEX EXPO 2024: ASMPT and Technica's Successful Partnership and Future Plans
05/08/2024 | Real Time with...IPC APEX EXPONolan Johnson speaks with Frank Medina and Jeff Timms about the fruitful collaboration between ASMPT and Technica and the upcoming launch of a machine with enhanced capabilities. They also discuss partnerships with semiconductor firms, customer demo plans, and the significance of the demo center. The conversation highlights the potential in North America.
Global Sourcing Spotlight: Golf, Friedman, and the Benefits of Global Sourcing
05/08/2024 | Bob Duke -- Column: Global Sourcing SpotlightWhen I started working on global sourcing for American Standard Circuits, a friend sent me a book by the NY Times economist Thomas Friedman called The Lexis and the Olive Tree. Well, not being a fan of the NYT or even economists as a whole, I put the book on a shelf and forgot about it until I got a call from my book-giving friend, and he asked me what I thought of the book. I mumbled something unintelligible and quickly changed the subject.
AT&S Brings High-Tech to the Museumsquartier
05/06/2024 | AT&SAT&S, as a “MQ goes Green” partner, has prepared special highlights for the occasion: Visitors aged eight and above can embark on an interactive journey through the fascinating world of microelectronics.
It’s Only Common Sense: Would You Join Your Own Company?
05/06/2024 | Dan Beaulieu -- Column: It's Only Common SenseIn the past few years, I have heard many company runners complaining about their workforce. They tell me that the government is paying people too much money not to work, too many young people are not interested in working every day, and there is just not the work ethic there once was when they were young.