DDR4: Not Your Grandfather’s DDR


Reading time ( words)

A long time ago, when DDR first came out, some of you may remember that it was difficult to design the interface. In my old board design team, we simulated the interface quite a bit to make sure that the system would function when the boards came back.

Then of course, the “been-there-done-that” attitude set in, and DDR became a design-by-numbers interface to push the schedule. Then came DDR2, which had many similarities to DDR.  By the time DDR3 came out, many people didn’t even bother to simulate the setups at some of the slower speeds. They’re largely leveraged from a previous design, so why bother?

And then comes DDR4.  This is the new guy in town who you can sense is a bit different. Questions come up:

  • What, you don’t have a fixed Vref? 
  • You’re going to have a new threshold every time you power up? Then how do you know whether you’re the signal is a 1 or a 0 if I don’t know what the threshold is beforehand? 
  • What do you mean you’re going to flip all the bits?

Then maybe it starts to sink in:

Maybe I should simulate this. So, just how good are the IBIS models for this anyway?  Can I trust them at these higher speeds?

nitinb0215-1.png

These are many of the questions we answered, along with our partners at Fujitsu and Micron, in the paper that has was nominated at DesignCon for a best paper award: DDR4 Board Design and Signal Integrity Verification Challenges

In the first half of the paper, we discuss the details of DDR4.  What exactly are Pseudo-Open Drain (POD) and Data-Bit Inversion (DBI), and why the Vref is so dodgy?  It will give you good background information about how DDR4 is different from DDR3.

In the second half, we compare the simulation results of a large setup between the older IBIS 4.2 spec, the newer IBIS 5.0 spec, and a transistor level Spice model.  Spoiler alert: the IBIS 5.0 results very closely match the transistor level Spice models – at a small fraction of the time needed to simulate.

nitinb0215-2.jpg

If you are designing a DDR4, and would like to confirm your board, this paper is a helpful reference in deciding what needs to be analyzed before and after releasing the board.

Download your copy of the paper here.

Share

Print


Suggested Items

Real Time with… IPC APEX EXPO: Siemens’ Supply Chain Solutions

01/17/2022 | Nolan Johnson, I-Connect007
Nolan Johnson speaks with Oren Manor of Siemens Digital Industries Software about the company’s booth at IPC APEX EXPO, which will highlight a DSI platform meant to help designers find and use components in their designs during these tough supply chain challenges. If you can’t make it to IPC APEX EXPO, don’t worry. We’ll be bringing you interviews with the engineers, managers and technologists who are making a difference in our industry.

A High-Voltage PCB Design Primer

01/12/2022 | Zachariah Peterson, NWES
Of all the different boards a designer can create, a high voltage PCB design can be complicated and requires strict attention to safety. If not laid out correctly these boards can be safety hazards or can fail to function on first power up, leaving a designer with wasted time and effort. In the best case, the board will function reliably for a long period of time thanks to correct layout practices. High-voltage PCB design can be as complex as any high-speed digital design. Boards for high-voltage systems can be space constrained and they carry important safety requirements. They also need to be highly reliable to ensure they will have a long life when run at high voltage and current.

High-Voltage PCB Design: Beating Separation Anxiety

01/11/2022 | I-Connect007 Editorial Team
In recent surveys, PCB designers named high voltage among the issues causing problems in their designs. That led us to speak with Zuken USA’s Andy Buja, Wilmer Companioni, and Sanu Warrier about the challenges PCB designers and design engineers must confront when working with high-voltage designs. In this conversation, we discuss everything from the nuts and bolts of high-voltage design, such as the need to separate components of a high-voltage board, to the compliance problems companies like Tesla face when installing EV chargers around the world in countries with varying regulations.



Copyright © 2022 I-Connect007. All rights reserved.