Behind the Design: Visteon®


Reading time ( words)

First place winner in the Transportation & Automotive category for the 2014 Technology Leadership Awards went to: Visteon, United States. 

Design: automotive heads-up display

Design team: Hai Pham, Padmanaban Kanagaraj, and Krzysztof Russa

Design challenges:

  • BGA connections
  • The connections between 0.80 mm pitch BGA microprocessor 624 pin 25 X 25, two DDR3 96 pin 16 X 16, one Flash 1 mm pitch 64 pin 8 X 8 and the 30 pin double side edge connector proved to be very challenging. The requirements were to place the traces in close proximity in order to minimize trace length. Utilizing Constraint Manager allowed the requirements to be met while complying with all design rules for performance and fabrication.
  • Through-hole vias used for cost; challenging to route to BGA.
  • Mechanical: keepouts for slots, holes, and metal contact with housing
  • Power management: eight power rails to microprocessor; decoupling requirements 
Visteon_Award_Winning_Design-520x186.jpg

Design tools and team comments:

  • Xpedition® Enterprise
  • Constraint Manager: Multiple net classes to manage signal integrity, EMI constraints
  • Hyperlynx PI was used to analyze decoupling capacitance for each group of circuits, such as power and GND plane areas, as well as the proximity of decoupling capacitors to the IC, and the number of vias and capacitors used.
  • Hyperlynx SI was used to measure and analyze circuit delay, cross talk, and impedance.
  • Hyperlynx Thermal was used to analyze component temperature and over PCB temperature to ensure the design met requirements.

Judges’ comments:

  • Excellent example of high-speed, higher-than-average density design using the latest design simulation and tools for new innovative features in autos.
  • This board was designed using standard layout technology. Tight interconnections to meet electrical requirements were compounded by strict mechanical limitations. Good description of what they went through to complete this design.

About the Technology Leadership Awards

Started in 1988, this program is the longest running competition of its kind in the electronic design automation (EDA) industry. It recognizes engineers and designers who use innovative methods and design tools to address today’s complex PCB systems design challenges and produce industry-leading products. See the full list of 2014 winners here.

Share




Suggested Items

I-Connect007 Editor’s Choice: Five Must-Reads for the Week

04/08/2022 | Andy Shaughnessy, Design007 Magazine
Spring has definitely sprung, and the trade show season continues to roll right along. Managing Editor Nolan Johnson just returned from DesignCon 2022, and as he says in his review, the attendance was up from last year’s event, which had been at the McEnery Convention Center in the waning days of the pandemic. I hope we’re getting back to normal, whatever that means. This week, we have a few articles about Industry 4.0, as well as a column on setting your priorities. We have a cool article about methods for measuring the breakdown of resins during multiple thermal laminations, and a conversation with an EMS company president who realized that he was actually running a data collection firm that happened to make circuit boards. Can you say the same about your own company?

DesignCon 2022: Back to Business as Usual

04/07/2022 | Nolan Johnson, I-Connect007
It was something of a homecoming as DesignCon returned to the Santa Clara Convention Center this week for DesignCon 2022. It’s been two years since the last DesignCon was held in this venue just before the pandemic began. I attended DesignCon 2021 at the San Jose McEnery Convention Center in July of last year, and I could see a big improvement in attendance as DesignCon moved back into its usual venue.

Setting Goals for Your PCB Design Education

03/30/2022 | Andy Shaughnessy, Design007 Magazine
For our March issue of Design007 Magazine on planning your design education, we spoke with Bill Brooks of Nordson ASYMTEK, a long-time PCB designer, CID instructor, and fantastic sculptor. He is also one of the first to ever teach standalone PCB design courses in a college. After he earned his certification to teach the IPC CID workshops, Bill served as an adjunct instructor at Palomar College near San Diego, teaching beginning and advanced PCB design classes for 10 years. I asked Bill to share his thoughts on setting up a PCB design education career plan, and the need to stay on top of your game as a PCB designer.



Copyright © 2022 I-Connect007. All rights reserved.