Gary Ferrari Shares His Thoughts on PCB Design and More


Reading time ( words)

Recently, I had a chance to talk with Gary Ferrari, the director of technical support at Firan Technology Group Corporation (FTG), on numerous topics related to PCB design. Our conversation ranged from CID training to the need for reaching high school students as a way of introducing more young people to career opportunities in our industry. We also covered strategies for helping customers design and build better product, and keeping designers provided with the most critical part of their supply chain—information.

Barry Matties: Gary, please begin by telling us a little bit about FTG.

Gary Ferrari: FTG is a circuit board manufacturer—that's the circuits division. Then we have an aerospace division and their products are keyboards, bezels, and panels for the avionics industry. When you look at all the gauges on the dashboard of a cockpit, you are looking at the items we manufacture.

Matties: Is it more for military applications? 

Ferrari: It’s for both commercial and military avionics. Our products are on helicopters and military aircraft. We're also on many of the commercial aircraft. We're on the new C919 from China. Actually, we have a plant to build those units over there. We have an aerospace and a circuits division in Toronto, as well as an aerospace and circuits division in Chatsworth, California.

Matties: What is your position at FTG?

Ferrari: I am the director of technical support—that means that I get into the customer prior to the design or during the design phase and I help them with their design issues. I look at manufacturability from a fabrication standpoint, as well as assembly, DFM, test, etc. I try to help them design a good product in the long run. That's where I serve best.

Matties: When you talk about working with customers, is that at the pre-circuit level when they are just imagining this stuff or is it beyond that?

Ferrari: They have already done the imagining, and now they need to bring it to the physical world. Sometimes they just don't understand the tolerances or the processes, the sequences in building a stack-up, material characteristics and combinations, buried vias and all those little details. I work with them so that they understand how to build something that's manufacturable and cost-effective. Anybody can design something, but when it comes down to getting fabricated, it could end up being a million-dollar design when it could have been maybe a thousand-dollar design, but they messed it all up. We try to help them out with that, and that's what my job is.

To read this entire article, which appeared in the July 2015 issue of The PCB Design Magazine, click here.

Share

Print


Suggested Items

This Month in Design007 Magazine: HDI Design, Landless Vias, VeCS, and More

11/09/2020 | I-Connect007 Editorial Team
Andy Shaughnessy, Happy Holden, and Dan Feinberg recently met with James Hofer, general manager of Accurate Circuit Engineering, to discuss via design techniques and via reliability from the fabricator’s viewpoint. As Hofer explained, even with open lines of communication between the designer and the board shop, there are plenty of variables to contend with regarding proper via design, especially when working with PTFE materials.

Roundtable Discussion: App Notes and Fab Notes

11/09/2020 | Andy Shaughnessy, Design007 Magazine
Andy Shaughnessy recently invited four recent contributors—Dana Korf, Jen Kolar, Mark Thompson, and Kelly Dack—to review the June and August 2020 issues of Design007 Magazine, which covered app notes and fab notes, respectively. In this wide-ranging roundtable, the group discusses some of the ongoing challenges related to incomplete and inaccurate design data and why communication can preclude many of these problems. What follows is the transcript from this conversation.

Real Time with… AltiumLive 2020: Vince Mazur Previews New Design Rule Features

11/03/2020 | I-Connect007 Editorial Team
Altium Technical Marketing Manager Vince Mazur discusses his presentation at the recent AltiumLive, which focused on updates to Altium Designer's approach to creating design rules and constraints. Vince explains that these features will be more intuitive for the user, and the update, which is currently in beta, will be released in the future. The company is shifting from “rule-centric” design rules features to capabilities that are more “design-centric,” with applicable rules for each object available at one click.



Copyright © 2020 I-Connect007. All rights reserved.