A Brief Overview of High-Frequency Laminates

Reading time ( words)

The PCB laminates used for high-frequency applications possess several unique attributes that are distinctly different than FR-4 types of materials. Obviously, the electrical properties are better for high-frequency laminates than FR-4, however there are many other beneficial characteristics which may be less obvious for those unfamiliar with these specialty laminates. These other properties are the reason why sometimes, high-frequency laminates are used for applications that are not high-frequency.

Moisture absorption can be problematic for high-frequency circuits (and other applications) for several reasons. When a circuit absorbs moisture from its environment, some water content becomes part of the material matrix on a molecular level. Water has a high dielectric constant, with a value of approximately 70. Most components that make up a laminate have dielectric constant values in the range of about 2–10, so if an appreciable amount of the material matrix has a component of 70, the overall laminate dielectric constant will increase significantly. A change in dielectric constant will cause a change in impedance, propagation velocity, phase response and other circuit issues. Additionally, the change due to moisture is typically a variable based on the environmental conditions in which the circuit is operating.

The amount of moisture absorption that can impact circuit performance is unique to the circuit design and application. Some applications are nearly unaffected by moisture absorption issues and others will have electrical performance that is greatly affected. The amount of moisture absorption which is considered low for high-frequency applications is somewhat subjective, but as a general rule a value of 0.3% or less is considered good. Moisture absorption also increases insertion loss, and as another general rule, the applications that are higher frequency or higher speed are more susceptible to moisture effects.

Other issues that are critical to many high-frequency applications and also environment-related is TCDk and TCDf. All circuit materials have these attributes: TCDk is the temperature coefficient of dielectric constant (Dk) and TCDf is analogous in regards to dissipation factor (Df). Basically, this is the property of material which will change Dk or Df with a change in temperature. Many times this becomes an issue when an application is fine-tuned in a lab environment and it then performs different in the field as the temperature fluctuates. The amount that TCDk or TCDf impacts circuit performance is very design and application specific. Some applications will be unaffected by these changes and others may see dramatic shifts of electrical performance.  An ideal TCDk or TCDf would be 0 ppm/°C, which gives no change in Dk or Df with a change in temperature, but this is typically not realistic. A general rule for a good TCDk is an absolute value of 70 ppm/°C; however, there are many applications which could tolerate 200 ppm/°C or even more.

To read this entire column, which appeared in the August 2015 issue of The PCB Design Magazine, click here.


Suggested Items

Designing for Material Conservation Means Changing Attitudes

08/29/2022 | I-Connect007 Editorial Team
It makes a lot of sense: During times when the supply chain is stretched to the breaking point—and the last few years certainly qualify—what if PCB designers created boards that used fewer components and less laminate? Do PCBs still have to be 0.062" thick? Why not reduce layer count while they’re at it? Andy Shaughnessy and Nolan Johnson spoke with I-Connect007 columnist Dana Korf about the idea of designing a PCB with material conservation in mind. Is it a great new idea, or are we opening a whole new can of worms and a separate group of problems?

The Practical Side of Using EM Solvers

08/01/2022 | Heidi Barnes, Keysight Technologies
Electromagnetic (EM) solvers based on Maxwell’s equations have proven invaluable in the advancement of digital electronics and wireline communications. Plain and simple, electrical engineers need to know what a circuit or electrical interconnect will do when excited by a dynamic or varying signal. In the signal integrity world, an interconnect that passes a DC connectivity check can completely fail at higher frequencies. In the power integrity world, a power rail that measures the correct DC voltage could easily go into oscillation when a dynamic load is applied. Learning the basic skills to fire up an EM simulator, obtain qualitative answers in minutes, and higher fidelity answers in a few days, can be the difference between sleepless nights of product failures vs. robust designs with wide design margins.

Producing Diverse Designs in Concert With Manufacturing

06/16/2022 | Scott Miller, FreedomCAD Services
There is a new acronym bubbling up in the design world: DWM, which stands for “design with manufacturing.” Why is this different than design for manufacturing, or DFM? With DWM, the emphasis is on integration between the design team and the manufacturers during the design process. DWM is much more than that. We are tasked with producing designs that meet various technical requirements, yet are cost-effective and manufacturable. We provide this service to hundreds of customers who have varying degrees of processes, tools, and manufacturing partners. Given this diversity, we have recognized the importance of designing with manufacturing to achieve the product development goals of manufacturability and technical excellence.

Copyright © 2022 I-Connect007. All rights reserved.