-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueLevel Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Speeding up the Design Cycle: 10 Things to Remember
November 11, 2015 | Mark Thompson, CID, Prototron CircuitsEstimated reading time: 2 minutes
Many people understand the value of a PCB, but do not understand the best way to interact with PCB manufacturers. Poor planning and communication with fabricators slows down the design cycle and increases overall costs for your project.
In this column, I will attempt to help streamline the design cycle through fabrication. Following my tips will minimize the need for future revisions and ensure you get quality boards on time.
10. Eliminate Conflicting Information
It is essential that you eliminate any conflicting information from your drawings or read-me files. Make sure that all documentation is the same. If one document says half-ounce and another says one-ounce copper, you may expect a call asking which it is to be. If you need the part expedited, remember that this takes valuable time away from the build and from you getting your part.
9. Provide an IPC Netlist
An IPC netlist will allow the fabricator to check your design against your exported data. Make sure any known or intentional netlist mismatches are noted again so your CAM group does not waste time calling you to check on things you are already aware of.
Be careful with castellated pads where plated half-holes at the board’s edge will make a connection to a post at some point after fabrication. These typically come up as “broken” or open nets because when the bare boards are fabricated, no post exists to connect these castellations.
Known A-gnd to D-gnd shorts should also be noted. Make sure no non-plated holes have been specified as test points on the IPC netlist. If you are specifying net-compare on your documentation, be sure to include it!
8. Check for Discrepancies on NC Drill File
Double-check to ensure there are no discrepancies of count, size or plating status on the NC drill file. Either one of these can cause communication delays.
7. Communicate With Your Fabricator ASAP
In order to facilitate the best communication, you need to meet with your chosen fabricator as soon as possible in the design cycle. Check with them for validation of any impedance you may have. Make sure these notes do not conflict either.
Be sure to: Check for proper reference planes. Make sure impedance traces do not traverse multiple splits or lack ref-planes altogether. Differentiate between single-ended and differential type structures by a tenth or a hundredth of a mil. Again, fabricators cannot resolve these small increments, but this allows the fabricator to uniquely select just the impedance tracks for any resizing that may be necessary to meet desired impedances.
Make sure the space between differential pairs is consistent throughout the run. Allow for process deviation, setting up a part as .1 mm trace and space on half-ounce starting copper does not leave room for any trace resizing that may be necessary to meet the impedances if dielectric cannot be altered.
When calling out materials, call out the 4101/# such as 4101/126. This will allow the fabricator to use any material that falls within the /126 criteria. Calling out a specific material may limit the pool of fabricators that can build the board. Avoid creating same net spacing violations when terminating differential pairs, and do not “wrap” the differential pairs around the terminus.
To read this entire column, which appeared in the October 2015 issue of The PCB Design Magazine, click here.
Suggested Items
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.
Trouble in Your Tank: Supporting IC Substrates and Advanced Packaging, Part 5
03/19/2024 | Michael Carano -- Column: Trouble in Your TankDirect metallization systems based on conductive graphite or carbon dispersion are quickly gaining acceptance worldwide. Indeed, the environmental and productivity gains one can achieve with these processes are outstanding. In today’s highly competitive and litigious environment, direct metallization reduces costs associated with compliance, waste treatment, and legal issues related to chemical exposure. What makes these processes leaders in the direct metallization space?
AT&S Shines with Purest Copper on World Recycling Day
03/18/2024 | AT&SThe Styrian microelectronics specialist AT&S is taking World Recycling Day as an opportunity to review the progress that has been made in recent months at its sites around the world in terms of the efficient use of resources: