Meaningful SPI Production Control Through Automatic Normalization


Reading time ( words)

Automated pre-placement solder paste inspection (SPI) has established itself in SMT assembly as an essential tool for optimizing the process and reducing end of line defects. It’s been commonly accepted for many years that a majority of assembly defects can be traced back to print defects, and by using raw measurement data from printed PCBs for volume, area, height and offset, SPC histograms and control charts can quite readily be used to optimize the process.

Following optimization, SPI is used to detect print anomalies. However, the multitude of “normal” variables introduced from board characteristics, clamping methodologies, stencil variations and paste type force unacceptably wide tolerance settings. These board-wide good/bad tolerances can easily mount to +/- 50% or more. For most, this is unacceptable, because of course, with such wide tolerances production drift can be missed and important defects ignored. 

Tolerances before and after Optimization are similar

Aperture Release

For example, stencil pattern variations cause differences between designed (expected) and actual solder release. For large apertures, release variation is generally negligible. Small apertures can account for up to 50% release variation or even more. Stencil thickness to aperture area ratio determines how close to 100% release efficiency is achievable. As pads get smaller and smaller, the area of the aperture wall approaches that of the pad area. In turn, the paste release efficiency is reduced as the adhesion forces from the walls approach that of the pad. Thus, different pad sizes across a board will exhibit different volume performance.   

A common work-around for this is possible by selecting specific areas and setting tolerances for these apertures.

Though these custom tolerance settings may be individually easy to perform, they are time consuming and do not carry over to other PCB’s due to differences in design, manufacture and finish. These differences are common practice in just in time manufacturing:

1. Solder mask thickness variations; typical thickness 25 um  +25/– 12um; Silk screen legends can add 12 um

2. Solder mask defined or non solder mask defined apertures

3. Gasketing effect variations

4. Solder pad finish

a. OSP and gold 0 %variation

b. HASL +/-20 um

5. Board Warpance:

These all create variations on the “zero reference height” point on each pad for measurement.

Mek Automated Normalization

Automated Normalization has been introduced by Mek SPI which directly addresses the excessive time required for board region based tolerance tightening. This unique 2 stage system allows the user to first optimize the printing process and then once the optimization has been completed, to automatically normalise the results and then set tighter tolerances to monitor product drift, enabling meaningful production control. The 5D measurement, combining 2D and 3D measurements ensures proper zero referencing, forming a solid base for accurate and repeatable measurements.

Tolerances after Normalization

The normalization extraction takes user selected average area, height and volume from several previous inspections when being set. Thus, an accurate representation of the capability of the print process is incorporated. If a process change, such as stencil or print settings need be made, the normalization extraction can be readily reset and then applied once again. www.marantz-electronics.com

About MEK (Marantz Electronics Ltd)

A former division of Marantz well known for its high quality Audio/Video products, MEK Japan (Marantz Electronics Kabushiki Kaisha), developed its first AOI system in 1994. Developed to inspect PCB assemblies for correct component placement and soldering, the company’s original AOI system was designed for use in Marantz factories. Proving to be a highly successful, cost-effective alternative to traditional human inspection, MEK developed its first generation commercial system in 1996. With a steadily growing installed base, MEK Japan and its European/American headquarters, MEK, have sold over 5000 units worldwide to date. Now well established as a leading force in AOI technologies, the company recently launched a 5D post-print SPI system which combines 3D and 2D image processing methodologies to deliver unprecedented defect detection. At the beginning of March 2014 the company opened US offices in Las Vegas.

Share




Suggested Items

Passing the Test With SMTA’s Rob Boguski

09/14/2022 | Andy Shaughnessy, I-Connect007
I recently spoke with Rob Boguski, president of Fremont, California-based Datest and an SMTA vice president and board member. Rob explained why today’s test customers are asking for more information than the traditional pass/fail, offers a preview of SMTA International, and gives an update on SMTA’s planning strategy for the next five years.

Four Silver Linings in the Stormy Clouds of Pandemic, Supply Chain, and Inflation

09/14/2022 | Dr. Ronald C. Lasky, Indium Corp.
It may be difficult to see any bright spots in the current and recent economic situation. We have all experienced the devastation of the pandemic, supply chain issues, and most recently, inflation. However, as a senior technologist for an international materials supplier (Indium Corporation) and a professor of engineering at an Ivy League research university (Dartmouth College), I offer these four silver linings for those of us in the electronics industry.

Solder Paste Printing and Optimizations for Interconnecting Back Contact Cells

07/26/2022 | Narahari S Pujari and Krithika PM, MacDermid Alpha Electronics Solutions
The interdigitated back contact (IBC) is one of the methods to achieve rear contact solar cell interconnection. The contact and interconnection via rear side theoretically achieve higher efficiency by moving all the front contact grids to the rear side of the device. This results in all interconnection structures being located behind the cells, which brings two main advantages. First, there is no frontside shading of the cell by the interconnection ribbons, thus eliminating the need for trading off series resistance, losses for shading losses when using larger interconnection ribbons. Second, a more homogeneous looking frontside of the solar module enhances the aesthetics.



Copyright © 2022 I-Connect007. All rights reserved.