-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueLevel Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Failure Mode: Hole Wall Pullaway
September 16, 2015 | Paul Reid, ConsultantEstimated reading time: 1 minute
Hole wall pullaway (HWPA) is an insidious defect that is not usually a cause of electrical failure. What happens with HWPA is that the copper plating in a plated through-hole (PTH) is pulled away from the dielectric of the drilled hole wall. The hole must not be filled with any sort of a hole fill in order to see HWPA.
There are two distinct types of HWPA: stress-relieving and stress-inducing. In stress-relieving HWPA, the condition appears to distress the PTH, allowing it to survive hundreds or thousands of thermal cycles without failure. In stress-inducing HWPA, the stress appears to greatly increase, causing the PTH to fail in just a few thermal cycles. What we consider a failure is an increase greater than 10% in the overall resistance in the circuit. A crack that partially bridges the copper at the internal interface is enough to cause a failure.
This column is based on my experience in test reliability of interconnect stress test (IST) coupons. I am addressing HWPA that features moderate to severe outgassing. There may be HWPA due to thermal stressing of the board without any significant outgassing, but this type of HWPA is subtle, and it presents as a dark line between the plating and the dielectric of the hole wall. This type of HWPA is rarely detected.
Stress-Relieving HWPA
Stress-relieving is the most common type of HWPA. It appears that the adhesion of copper plating to the dielectric is reduced most likely due to problems with the application of electroless copper plating adhering to the dielectric of the hole wall. At the same time, the adhesion is strong at the copper’s internal interconnection. In fact, experience suggests that the adhesion of the electroless copper is stronger than the copper plating. This process frequently produces strong interconnections to copper inner layers. This condition may result in a hole wall that looks like a stack of forward or backward “Ds” running the length of the hole where the top and the bottom of the “Ds” is at an internal interconnect.
To read this entire article, which appeared in the August 2015 issue of The PCB Design Magazine, click here.
Suggested Items
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.
Trouble in Your Tank: Supporting IC Substrates and Advanced Packaging, Part 5
03/19/2024 | Michael Carano -- Column: Trouble in Your TankDirect metallization systems based on conductive graphite or carbon dispersion are quickly gaining acceptance worldwide. Indeed, the environmental and productivity gains one can achieve with these processes are outstanding. In today’s highly competitive and litigious environment, direct metallization reduces costs associated with compliance, waste treatment, and legal issues related to chemical exposure. What makes these processes leaders in the direct metallization space?